.quickedit{ display:none; }
Selamat datang di blog yang sederhana ini....Terimakasih Atas kunjungan Anda diblog ini...!! Semoga Anda tidak bosan dengan isi Blog ini dan Anda bisa kembali berkunjung lagi.

Selasa, 28 Desember 2010

Kode Rahasia Windows Phone

Kali ini saya mencoba untuk memberikan petunjuk untuk mengetahui kode rahasia windows phone.Dari mode ponsel kamu bisa menampilkan informasi detail tentang jaringan GSM yang sedang digunakan. Caranya, klik Star - Phone. Pada layar telepon akan muncul, tekan *#0228#. Begitu tombol # ditekan akan muncul jendela Monitor GSM.
Bagian atas menmpilkan Antena RSSI yg menunjukkankualitas sinyal dari operator kamu dalam satuan db. dibawahnya, Antena Bar menampilkan jumlah bar dari sinyal kamu. dibagian Serving Cell, tampil jaringan GSM yg sedang digunakan. dibagian bawah terpampang informasi tentang baterai yg dipakai, suhu, jenis, kapasitas, jumlah bar, juga voltasenya. disamping shortcut diatas, ada shortcut2 lain yg bisa dicoba :
1. *#2470# untuk update firmware kamera
2. *#0673# untuk mengetes suara
3. *#0842# untuk mengetes efek getar dan latar
4. *#1111# untuk menampilkan versi software
5. *#1234# untuk menampilkan informasi software
6. *2767*3855# untuk melakukan hard reset tanpa peringatan
7. *#0002*28346# untuk menganti setting volume

selamat mencoba......!!!
sumber PCplus

Selasa, 14 Desember 2010

Cara mereset Cartridge Canon CLI-8BK

Beberapa kartrid Canon buat cetak dilengkapi dengan microchip yang memungkinkan printer dan perangkat lunak Canon pada komputer tahu apakah kartrid tinta telah terbaca seara langsung dari Canon atau telah diisi ulang. Jika kartrid telah digunakan sebelumnya, maka printer tidak akan bekerja sampai Canon kartrid cetak baru dipasang.Untuk menghemat uang, beberapa orang baik isi ulang kartrid cetak sendiri atau mereka membeli cartridge diisi ulang secara online. Ada cara untuk mereset microchip untuk cartridge Canon CLI-8BK tinta sehingga akan bekerja di printer
Mengatur ulang Chip
Beli Canon resetter chip, yang tersedia melalui beberapa toko isi ulang tinta kartrid online.Hapus isi ulang atau aftermarket Canon CLI-8BK cartridge dari kemasannya.Tempatkan kartrid tinta pada chip resetter. Pastikan ujung chip pada bagian bawah cartridge ditekan melawan pin resetter untuk membuat koneksi.Tunggu lampu LED pada kartrid tinta berkedip sekali, kemudian menyala padat. Ini berarti chip pada kartrid tinta telah direset dan sekarang akan bekerja di printer. Hidupkan Printer dan buka tutup pintu printer dan Lepaskan cartridge lama dan menginstal cartridge yg baru. Tutup pintu printer dan mulai menggunakan printer.


Selamat Mencobaa.....

Cara Mereset Printer Canon MX328


Solution to reset the ink level for Canon MX328, follow the step below :

1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The printes turns into a kind of factory mode...(wait for about 10 seconds, utils it says "Idle")
6. Press the ">" (next to the "OK" button) once."Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print.
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back
Methode 2 :
Canon Pixma MX328 is one of the Inkjet multifuction (Print, Scan, Copy, Fax) printer from Canon. Like general case of printer, after filled by ink usually ink level not full. At some cases of printer, after ink level empty, printer cannot be used to print.
Here the Solution to reset the ink level for Canon Pixma MX328 follow this steps to reset the ink level in your canon MX328.
1. Switch off the Canon MX328 and disconnect the power cable.
2. While press and hold the power button, Connect the power cable to electric socket.
3. While pressing the power button, press the “Cancel/Stop” button (red button).
4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says “idle”.
5. Press “>” (next button) once “Shipping Mode 3? then Press the “OK” button. Press “OK” again for “without cleaning”.
6. A test page will print.
7. Open the cover, like you are about to change the cartridges.
8. Disconnect the power cable again without switch off the printer.
9. Take out the both cartridges.
10. Close the cover.
11. Connect the power cable and turn on the printer.
12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.
Last step reset permanently with Service Mode Tool.
For the software you can download link below :
mx328_ServiceModeToolsVersion1.050.exe

Adhe edogawa.

Check Page Rank Blog/Web site Anda disini:

This page rank checking tool is powered by Page Rank Checker service

Like Facebook

Pengikut